[Free] 2018(Jan) EnsurePass Examcollection Juniper JN0-332 Dumps with VCE and PDF Download 291-300

Ensurepass.com : Ensure you pass the IT Exams 2018 Jan Juniper Official New Released JN0-332
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-332.html

Juniper Networks Certified Internet Specialist, SEC (JNCIS-SEC)

Question No: 291 – (Topic 3)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Referring to the exhibit, you are not able to telnet to 192.168.10.1 from client PC 192.168.10.10. What is causing the problem?

  1. Telnet is not being permitted byself-policy.

  2. Telnet is not being permitted by security policy.

  3. Telnet is not allowed because it is not considered secure.

  4. Telnet is not enabled as a host-inbound service on the zone.

Answer: D

Question No: 292 – (Topic 3)

What are three main phases of an attack? (Choose three.)

  1. DoS

  2. exploit

  3. propagation

  4. port scanning

  5. reconnaissance

Answer: B,C,E

Question No: 293 – (Topic 3)

Which card performs flow lookup on incoming packets on high-end SRX Series devices?

  1. Network Processing Card (NPC)

  2. Services Processing Card (SPC)

  3. Switch Control Board (SCB)

  4. Routing Engine (RE)

Answer: A

Question No: 294 – (Topic 3)

Regarding attacks, which statement is correct?

  1. Both DoS and propagation attacks exploit and take control of all unprotected network devices.

  2. Propagation attacks focus on suspicious packet formation using the DoS SYN-ACK- ACK proxy flood.

  3. DoS attacks are directed at the network protection devices, while propagation attacks are directed at the servers.

  4. DoS attacks are exploits in nature, while propagation attacks use trust relationships to take control of the devices.

Answer: D

Question No: 295 – (Topic 3)

ReviewBelow:

Ensurepass 2018 PDF and VCE

Which type of NAT is configured in the exhibit?

  1. static destination NAT

  2. static source NAT

  3. pool-based destination NAT without PAT

  4. pool-based destination NAT with PAT

Answer: C

Question No: 296 – (Topic 3)

You are required to configure a SCREEN option that enables IP source route option detection.

Which two configurations meet this requirement? (Choose two.)

  1. [edit security screen] user@host# show

    ids-option protectFromFlood { ip {

    loose-source-route-option;

    strict-source-route-option;

    }}

  2. [edit security screen] user@host# show

    ids-option protectFromFlood { ip {

    source-route-option;

    }}

  3. [edit security screen] user@host# show

    ids-option protectFromFlood { ip {

    record-route-option; security-option;

    }}

  4. [edit security screen] user@host# show

ids-option protectFromFlood { ip {

strict-source-route-option; record-route-option;

}}

Answer: A,B

Question No: 297 – (Topic 3)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Assuming you want to configure a route-based VPN, which command is required to bind the VPN to secure tunnel interface st0.0?

  1. set ipsec vpn remote-vpn bind-interface st0.0

  2. set ike gateway remote-ike bind-interface st0.0

  3. set ike policy ike-policy1 bind-interface st0.0

  4. set ipsec policy vpn-policy1 bind-interface st0.0

Answer: A

Question No: 298 – (Topic 3)

What is a zone?

  1. a set of rules that controls traffic from a specified source to a specified destination using a specified service

  2. a collection of one or more network segments sharing identical security requirements

  3. a method of providing a secure connection across a network

  4. a tool to protect against DoS attacks

Answer: B Explanation:

A zone is a collection of one or more network segments sharing identical security requirements.To group network segments within a zone, you must assign logical interfaces from the device to a zone.

Topic 4, Volume D

Question No: 299 – (Topic 4)

You have just configured source NAT with a pool of addresses within the samesubnet as the egress interface.

What else must be configured to make the addresses in the pool usable?

  1. static NAT

  2. destination NAT

  3. address persistence

  4. proxy ARP

Answer: D

Question No: 300 – (Topic 4)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Referring to the exhibit, you need to allow FTP traffic from the Internet to the FTP server in the Trust zone. You have built a custom application so that you can modify the timeout

value for FTP sessions and have configured a policy to allow FTP traffic from Untrust to Trust, but the traffic still does not flow. The current status of the FTP ALG is disabled.

What is the problem?

  1. The FTP ALG has not been enabled in the security policy.

  2. The FTP ALG has not been enabled in the security zones.

  3. The FTP ALG has been disabled on the device.

  4. The FTP ALG has not been set in the custom application definition.

Answer: C

100% Ensurepass Free Download!
Download Free Demo:JN0-332 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-332 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.